COMMISSIONING OF COMBINED CYCLE POWER PLANTS

Preparation, Planning, Pre-Commissioning Checks and Tests, Detailed Commissioning Procedures And Instructions For Each Equipment In A Combined Cycle Power Plant, Instrumentation, Trial Run Of Each Equipment, Safety And Precautions, Commissioning Of Combined Cycle Power Plant Systems, Safety Rules Clearance Certificates, And Reliability Test Of Combined Cycle Power Plants.

18 - 22 NOVEMBER 2019, KUALA LUMPUR, MALAYSIA

About The Course

This seminar provides a comprehensive understanding of all the commissioning procedures for combined cycle power plants. The Commissioning Management System of combined cycle power plants is covered in detail in this seminar.  This includes all the commissioning procedures and documents, purpose of commissioning, responsibilities, system description, organization, working parties, test teams, documentation, testing and commissioning schedules, test reports, safety, plant certification, and plant completion report.

 

The seminar provides also a thorough understanding of all the commissioning requirements for gas turbines, steam turbines and auxiliaries, generator and auxiliaries, electrical equipment, switchgear equipment, switchgear, and transformers. All the stages of the commissioning procedure are covered in-depth in this seminar.

 

This includes preparation – planning various activities, pre-commissioning checks and tests, typical commissioning schedule, detailed tests and commissioning procedures and instructions for every component in a combined cycle power plant, instrumentation, trial run of the equipment, safety and precautions, commissioning of combined cycle power plant systems, Safety Rules Clearance Certificates, procedure for the control and handling of defects, Commissioning Reports, operational testing, first fire, generator synchronization, performance testing, heat rate testing, emission testing, contract testing, CO2 concentration tests, electrical full-load rejection test, duct burner testing, partial load stability test, and reliability test.

 

This seminar is a MUST for anyone who is involved in the pre-commissioning or commissioning of any combined cycle power plant equipment because it provides detailed pre-commissioning checks and tests and detailed tests and commissioning procedures and instructions for every component in a combined cycle power plant.  In addition, the seminar provides in-depth coverage of all preparation, planning activities, commissioning schedules, trial run of each combined cycle power plant equipment, safety and precautions, Safety Rules Clearance Certificates, Procedures for handling defects, and Commissioning Reports.

Learning Outcomes

  • Pre-Commissioning Checks and Tests, Detailed Tests and Commissioning Procedures and Instructions for Every Equipment in Combined Cycle Power Plants: Gain a thorough understanding of all pre-commissioning checks and tests, and all commissioning procedures and instructions for every equipment in combined cycle power plants
  • Commissioning Management System of Combined Cycle Power Plants: Discover the benefits of the Commissioning Management System of combined cycle power plants including all commissioning procedures and documents, purpose of commissioning, responsibilities, system description, organization, working parties, test teams, documentation, testing and commissioning schedules, test reports, safety, plant certification, and plant completion report
  •  Commissioning Procedures and Instructions for Heat Recovery Steam Generators, Air Blow and Steam Blow of Steam and Gas Piping in Combined Cycle Power Plants: Learn about the commissioning procedures and instructions for heat recovery steam generators, chemical cleaning of heat recovery steam generators, air blow and gas blow of steam and gas piping in combined cycle power plants, safety valve setting, and soot blowers
  • Commissioning Procedures and Instructions for Gas Turbines and Steam Turbines: Gain a thorough understanding of all the commissioning procedures and instructions for gas and steam turbines and auxiliaries including acid cleaning of oil pipelines, lubrication and governing system (oil flushing and hydraulic testing), jacking oil system, governing system, regenerative system, barring gear, vacuum tightness test, first rolling of turbine and data logging
  • Commissioning Procedures and Instructions for Generator and Auxiliaries: Discover all the commissioning procedures and instructions for generator and auxiliaries including generator, seal oil system, hydrogen gas system, stator water system, rolling and start-up of generators
  • Commissioning Procedures and Instructions for Electrical Equipment: Learn about all the commissioning procedures and instructions for electrical equipment including switchyard equipment, switchgear, transformers, and motors
  • Operational Testing, Performance Testing, Heat Rate Testing, Emission Testing of Combined Cycle Power Plants: Gain a thorough understanding of operational testing, first fire, generator synchronization, performance testing, heat rate testing, emission testing, contract testing, CO2 concentration tests, electrical full-load rejection test, duct burner testing, partial load stability test, and reliability test of combined cycle power plants

Who Should Attend

  • Engineers of all disciplines
  • Managers
  • Technicians
  • Maintenance personnel
  • Other technical individuals

Expert Course Faculty

The trainer has been a teacher at University of Toronto and Dalhousie University, Canada for more than 25 years. In addition, He has taught courses and seminars to more than four thousand working engineers and professionals around the world, specifically Europe and North America. He has been consistently ranked as “Excellent” or “Very Good” by the delegates who attended his seminars and lectures.

 

The trainer wrote 5 books for working engineers from which three have been published by McGraw-Hill, New York.  Below is a list of the books authored by him:

  1. Power Generation Handbook: Gas Turbines, Steam Power Plants, Co-generation, and Combined Cycles, second edition, (800 pages), McGraw-Hill, New York, October 2011.
  2. Electrical Equipment Handbook (600 pages), McGraw-Hill, New York, March 2003.
  3. Power Plant Equipment Operation and Maintenance Guide (800 pages), McGraw-Hill, New York, January 2012.
  4. Industrial Instrumentation and Modern Control Systems (400 pages), Custom Publishing, University of Toronto, University of Toronto Custom Publishing (1999).
  5. Industrial Equipment (600 pages), Custom Publishing, University of Toronto, University of Toronto, University of Toronto Custom Publishing (1999).

 

The trainer has received the following awards:

  1. The first “Excellence in Teaching” award offered by Poweredge Asia Training center, Singapore, December 2016
  2. The first “Excellence in Teaching” award offered by the Professional Development Center at University of Toronto (May, 1996).
  3. The “Excellence in Teaching Award” in April 2007 offered by TUV Akademie (TUV Akademie is one of the largest Professional Development centre in world, it is based in Germany and the United Arab Emirates, and provides engineering training to engineers and managers across Europe and the Middle East).
  4. Awarded graduation “With Distinction” from Dalhousie University when completed Bachelor of Engineering degree (1983).
  5. Entrance Scholarship to University of Ottawa (1984).
  6. Natural Science and Engineering Research Counsel (NSERC) scholarship towards graduate studies – Master of Applied Science in Engineering (1984 – 1985).

The trainer performed research on power generation equipment with Atomic Energy of Canada Limited at their Chalk River and Whiteshell Nuclear Research Laboratories.  He also has more than 32 years of practical engineering experience with Ontario Power Generation (OPG – formerly, Ontario Hydro – the largest electric utility in North America). He retired from OPG in November 2016.

 

While working at Ontario Hydro, he acted as a Training Manager, Engineering Supervisor, System Responsible Engineer and Design Engineer. During the period of time that the trainer worked as a Field Engineer and Design Engineer, he was responsible for the operation, maintenance, diagnostics, and testing of gas turbines, steam turbines, generators, motors, transformers, inverters, valves, pumps, compressors, instrumentation and control systems. Further, his responsibilities included designing, engineering, diagnosing equipment problems and recommending solutions to repair deficiencies and improve system performance, supervising engineers, setting up preventive maintenance programs, writing Operating and Design Manuals, and commissioning new equipment.

 

Later, he worked as the manager of a section dedicated to providing training for the staff at the power stations.  The training provided by him covered in detail the various equipment and systems used in power stations.

 

The trainer was awarded his Bachelor of Engineering Degree “with distinction” from Dalhousie University, Halifax, Nova Scotia, Canada. He also received a Master of Applied Science in Engineering (M.A.Sc.) from the University of Ottawa, Canada. He is also a member of the Association of Professional Engineers in the province of Ontario, Canada.

TOPICS COVERED

Commissioning Management System

System Turnover from Construction to Commissioning

Chemical Cleaning of Heat Recovery System

Commissioning of DC Power and UPS System

Feedwater and Condensate

HRSG

Stator Water System

Transformer Pre-Commissioning Tests

Duct Burner Testing

This training course has a limited attendance for up to 20 participants only. Sessions commence at 9am on all days, with short intervals at 10.30am and 3.30pm respectively. 
Refreshments will be provided in the short intervals. Lunch will be provided at 12:30pm for 1 hour. Sessions will end at 5pm on all days.

Unique Features with powerEDGE Training

• Pre-Course Questionnaire to help us focus on your learning objectives
• Detailed Course & Reference Manual for Continuous Learning and Sharing
• Practical Exercises & Case Examples to better understand the principles
• Limited class size to ensure One-to-One Interactivity
• Assessment at the end of the course to help you develop a Personal Action Plan