27 - 29 JUNE 2018, KUALA LUMPUR, MALAYSIA
About The Course
This seminar will provide a comprehensive understanding of the various types of transformer maintenance including breakdown maintenance, preventive maintenance, total productive maintenance, condition-based maintenance, pro-active maintenance, and reliability-centered maintenance. All the expected problems in dry and oil-filled transformers will be discussed in detail. All the diagnostics, troubleshooting and maintenance required to ensure adequate operation of transformers will be covered thoroughly. This seminar will focus on maximizing the efficiency, reliability, and longevity of all types of transformers by providing an understanding of all commissioning requirements, repair and refurbishment methods of transformers.
This seminar is a MUST for anyone who is involved in the selection, applications, or maintenance of transformers because it covers how this equipment should be commissioned, the latest maintenance techniques, and provides guidelines and rules that ensure successful operation of this equipment. In addition, this seminar will cover in detail all protective systems, advanced fault detection techniques, critical components, dissolved gas analysis, and all transformer tests and commissioning requirements and procedures.
This seminar will provide the following information for all types of transformers:
- Preventive Maintenance, Condition-Based Maintenance, Pro-Active Maintenance, and Reliability-Centered Maintenance
- Pre-Commissioning and Commissioning Procedures
- Codes and Standards
- Common Operational Problems
- All Diagnostics and Troubleshooting Techniques
- Procedures for Type Tests, Routine Tests and Special Tests
- All Repair and Refurbishment Methods
- Protective Systems
- Equipment Diagnostics and Inspection: Learn in detail all the diagnostic techniques and inspections required of critical components of transformers
- Equipment Testing: Understand thoroughly all the routine tests, type tests, and special tests required for the various types of transformers
- Equipment Maintenance and Troubleshooting: Determine all the maintenance and troubleshooting activities required to minimize transformer downtime and operating cost
- Equipment Repair and Refurbishment: Gain a detailed understanding of the various methods used to repair and refurbish transformers
- Efficiency, Reliability, and Longevity: Learn the various methods used to maximize the efficiency, reliability, and longevity of transformers
- Equipment Sizing: Gain a detailed understanding of all the calculations and sizing techniques used for transformers
- Design Features: Understand all the design features that improve the efficiency and reliability of transformers
- Equipment Selection: Learn how to select all types of transformers by using the performance characteristics and selection criteria that you will learn in this seminar
- Equipment Commissioning: Understand all the commissioning requirements for transformers
- Equipment Codes and Standards: Learn all the codes and standards applicable for transformers
- Equipment Causes and Modes of Failure: Understand the causes and modes of failure in transformers
- System Design: Learn all the requirements for designing different types of transformer systems
Who Should Attend
- Engineers of all disciplines
- Maintenance personnel
- Other technical individuals
Course Faculty - Philip Kiameh
Has more than 32 years of practical engineering experience with Ontario Power Generation as an Engineering Supervisor and Training Manager, has conduct courses and seminars, to more than 4,000 working engineers and professionals who consistently ranked him as “Excellent” or “Very Good”. Philip has also wrote 5 books for working engineers from which three have been published by McGraw-Hill, New York.
Philip Kiameh, M.A.Sc., B.Eng., D.Eng., P.Eng. (Canada) has been a teacher at University of Toronto and Dalhousie University, Canada for more than 25 years. In addition, Prof Kiameh has taught courses and seminars to more than four thousand working engineers and professionals around the world, specifically Europe and North America. Prof Kiameh has been consistently ranked as “Excellent” or “Very Good” by the delegates who attended his seminars and lectures.
Prof Kiameh wrote 5 books for working engineers from which three have been published by McGraw-Hill, New York. Below is a list of the books authored by Prof Kiameh:
1- Power Generation Handbook: Gas Turbines, Steam Power Plants, Co-generation, and Combined Cycles, second edition, (800 pages), McGraw-Hill, New York, October 2011.
2- Electrical Equipment Handbook (600 pages), McGraw-Hill, New York, March 2003.
3- Power Plant Equipment Operation and Maintenance Guide (800 pages), McGraw-Hill, New York, January 2012.
4- Industrial Instrumentation and Modern Control Systems (400 pages), Custom Publishing, University of Toronto, University of Toronto Custom Publishing (1999).
5- Industrial Equipment (600 pages), Custom Publishing, University of Toronto, University of Toronto, University of Toronto Custom Publishing (1999).
Prof. Kiameh has received the following awards:
- The first “Excellence in Teaching” award offered by Poweredge Pte Ltd Training Center, Singapore, December 2016
- The first “Excellence in Teaching” award offered by the Professional Development Center at University of Toronto (May, 1996).
- The “Excellence in Teaching Award” in April 2007 offered by TUV Akademie (TUV Akademie is one of the largest Professional Development centre in world, it is based in Germany and the United Arab Emirates, and provides engineering training to engineers and managers across Europe and the Middle East).
- Awarded graduation “With Distinction” from Dalhousie University when completed Bachelor of Engineering degree (1983).
- Entrance Scholarship to University of Ottawa (1984).
- Natural Science and Engineering Research Counsel (NSERC) scholarship towards Graduate studies – Master of Applied Science in Engineering (1984 – 1985).
Prof. Kiameh performed research on power generation equipment with Atomic Energy of Canada Limited at their Chalk River and Whiteshell Nuclear Research Laboratories. He also has more than 32 years of practical engineering experience with Ontario Power Generation (OPG – formerly, Ontario Hydro – the largest electric utility in North America). Prof. Kiameh retired from OPG in November 2016.
While working at Ontario Hydro, Prof. Kiameh acted as a Training Manager, Engineering Supervisor, System Responsible Engineer and Design Engineer. During the period of time that Prof Kiameh worked as a Field Engineer and Design Engineer, he was responsible for the operation, maintenance, diagnostics, and testing of gas turbines, steam turbines, generators, motors, transformers, inverters, valves, pumps, compressors, instrumentation and control systems. Further, his responsibilities included designing, engineering, diagnosing equipment problems and recommending solutions to repair deficiencies and improve system performance, supervising engineers, setting up preventive maintenance programs, writing Operating and Design Manuals, and commissioning new equipment.
Later, Prof Kiameh worked as the manager of a section dedicated to providing training for the staff at the power stations. The training provided by Prof Kiameh covered in detail the various equipment and systems used in power stations.
Professor Philip Kiameh was awarded his Bachelor of Engineering Degree “with distinction” from Dalhousie University, Halifax, Nova Scotia, Canada. He also received a Master of Applied Science in Engineering (M.A.Sc.) from the University of Ottawa, Canada. He is also a member of the Association of Professional Engineers in the province of Ontario, Canada.
Types and Construction of Transformers
Transformer Component Selection
Transformer Quality Assurance
Transformer Best Maintenance Practices
Expected Problems in Transformers
Core/Winding Movement Tests
Transformer Routine Tests
Commissioning of Transformers
This training course has a limited attendance for up to 20 participants only. Sessions commence at 9am on all days, with short intervals at 10.30am and 3.30pm respectively. Refreshments will be provided in the short intervals. Lunch will be provided at 12:30pm for 1 hour. Sessions will end at 5pm on all days.
Unique Features with powerEDGE Training
• Pre-Course Questionnaire to help us focus on your learning objectives
• Detailed Course & Reference Manual for Continuous Learning and Sharing
• Practical Exercises & Case Examples to better understand the principles
• Limited class size to ensure One-to-One Interactivity
• Assessment at the end of the course to help you develop a Personal Action Plan